Review by CoMod JoergW of Carrera DIGITAL 124 the Carrera DIGITAL 124 /132 Pit Lane
(Item No. 30356)
After the fuel level has been set on the Main Unit in 10% increments, the Driver Display initially shows all lights, which then fade more or less quickly depending on driving style.
Once all green LEDs have gone out and the display enters the red LED zone, a pit stop is indicated. Toward the end of the red phase, the need for a refueling stop is additionally indicated by the vehicle’s lights flashing rapidly. If the warnings are ignored, laps will no longer be counted when passing through the Control Unit and/or Pit Stop Lane, and the display on the Position Tower will freeze. However, you’ll only notice this if you’re in the lead, since the display shows your laps. sind.Nach When entering the pit lane, you must hold down the refueling button until the desired fuel level is reached!
If you forget, you’ll be there a little longer ;-)
There are two fuel modes: normal and real. But I didn’t notice any significant difference during my tests on the small track. On the large track, with more high-speed sections, things could look quite different.
CoMod Joerg
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
Test report by CoModCarrera 124 on Carrera DIGITAL 124 the Carrera DIGITAL 124 /132 Pit Lane
(Item No. 30356) and Pit Stop Adapter Unit (Item No. 30361)
New to the pit lane is the single-lane straight where refueling takes place. This is also available separately, making it easy to retrofit the old pit lane.
Unlike the models shown at the Toy Fair, the single-lane straight does not have a direct electrical connection to the Control Unit. This means you can integrate the pit lane into the track layout however you like.
If you decide to install the pit lane parallel to the Control Unit (i.e., with the entrance before the Control Unit and the exit after it), the old pit lane had the problem that the laps of the refueling cars were not counted. This problem has been solved with the new refueling straight. Thanks to the corresponding sensor on the top of the track, a lap is counted even during the refueling process.
This function can also be disabled if you do not want to place the pit lane parallel to the Control Unit, but rather in a different location. To do this, the single-lane straight must be temporarily attached directly to the Control Unit. Next, a programming sequence is performed on the control unit. The setting configured in this way is permanently saved.
However, the sensor counts any pass through as a refueling stop, regardless of how long it lasted. Even a simple drive-through is counted as a refueling stop.
Important: You should only include a single refueling stop straight within a pit lane! Otherwise, a single pass through will be counted as multiple refueling stops. This behavior can only be prevented by disabling the refueling function on the Control Unit entirely.
You might now consider not using a pit lane at all, but instead misusing the refueling straights as an extension of the timing system for a potential third and fourth lane. However, this is not recommended, as the data protocol will likely result in timing inaccuracies in the lap times. For the intended use in the pit lane, these potential inaccuracies are hardly significant, since the key factor there is that the pit stop is recorded as a completed lap at all.
Refueling
Back to refueling! This process works a little differently than before: first, don’t let the marked refueling zone confuse you, as it’s quite short. The usable area for refueling extends from the point where you cross the pit stop sensor to the exit of the pit lane. The refueling process itself no longer happens automatically; you must hold down the soft key on your hand controller. On the driver display, you can then watch as the tank miraculously “fills up” again. However, refueling to full capacity is not mandatory; you can cancel the refueling process at any time and continue driving.
Fuel Level
The maximum possible fuel level
for the vehicles can be programmed on the Control Unit. A new feature is the ability to set a one-time exception to this limit for the race start. This is done via an additional programming sequence on the Control Unit; a Driver Display is also required to show the set fuel capacity.
CoModCarrera 124
(Item No. 30356)
After the fuel level has been set on the Main Unit in 10% increments, the Driver Display initially shows all lights, which then fade more or less quickly depending on driving style.
Once all green LEDs have gone out and the display enters the red LED zone, a pit stop is indicated. Toward the end of the red phase, the need for a refueling stop is additionally indicated by the vehicle’s lights flashing rapidly. If the warnings are ignored, laps will no longer be counted when passing through the Control Unit and/or Pit Stop Lane, and the display on the Position Tower will freeze. However, you’ll only notice this if you’re in the lead, since the display shows your laps. sind.Nach When entering the pit lane, you must hold down the refueling button until the desired fuel level is reached!
If you forget, you’ll be there a little longer ;-)
There are two fuel modes: normal and real. But I didn’t notice any significant difference during my tests on the small track. On the large track, with more high-speed sections, things could look quite different.
CoMod Joerg
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
Test report by CoMod
(Item No. 30356) and Pit Stop Adapter Unit (Item No. 30361)
New to the pit lane is the single-lane straight where refueling takes place. This is also available separately, making it easy to retrofit the old pit lane.
Unlike the models shown at the Toy Fair, the single-lane straight does not have a direct electrical connection to the Control Unit. This means you can integrate the pit lane into the track layout however you like.
If you decide to install the pit lane parallel to the Control Unit (i.e., with the entrance before the Control Unit and the exit after it), the old pit lane had the problem that the laps of the refueling cars were not counted. This problem has been solved with the new refueling straight. Thanks to the corresponding sensor on the top of the track, a lap is counted even during the refueling process.
This function can also be disabled if you do not want to place the pit lane parallel to the Control Unit, but rather in a different location. To do this, the single-lane straight must be temporarily attached directly to the Control Unit. Next, a programming sequence is performed on the control unit. The setting configured in this way is permanently saved.
However, the sensor counts any pass through as a refueling stop, regardless of how long it lasted. Even a simple drive-through is counted as a refueling stop.
Important: You should only include a single refueling stop straight within a pit lane! Otherwise, a single pass through will be counted as multiple refueling stops. This behavior can only be prevented by disabling the refueling function on the Control Unit entirely.
You might now consider not using a pit lane at all, but instead misusing the refueling straights as an extension of the timing system for a potential third and fourth lane. However, this is not recommended, as the data protocol will likely result in timing inaccuracies in the lap times. For the intended use in the pit lane, these potential inaccuracies are hardly significant, since the key factor there is that the pit stop is recorded as a completed lap at all.
Refueling
Back to refueling! This process works a little differently than before: first, don’t let the marked refueling zone confuse you, as it’s quite short. The usable area for refueling extends from the point where you cross the pit stop sensor to the exit of the pit lane. The refueling process itself no longer happens automatically; you must hold down the soft key on your hand controller. On the driver display, you can then watch as the tank miraculously “fills up” again. However, refueling to full capacity is not mandatory; you can cancel the refueling process at any time and continue driving.
Fuel Level
The maximum possible fuel level
for the vehicles can be programmed on the Control Unit. A new feature is the ability to set a one-time exception to this limit for the race start. This is done via an additional programming sequence on the Control Unit; a Driver Display is also required to show the set fuel capacity.
CoMod
